Nissan Juke : Juke Forums banner

81 - 100 of 115 Posts

·
Super Moderator
Joined
·
11,140 Posts
Question. While you are rolling. You are holding 5psi. That doesnt seem right.
 

·
Registered
Joined
·
275 Posts
Discussion Starter #82 (Edited)
Question. While you are rolling. You are holding 5psi. That doesnt seem right.
It holds 5-6psi while keeping the throttle half open, if I go open throttle(WOT) goes to 22psi, the only way to go -19 is releasing the pedal, driving feels normal, and idles exactly at 800 rpm, please what could be wrong to take a look at it.
 

·
Super Moderator
Joined
·
11,140 Posts
Well just driving along you should not be in boost at all.

Where do you have it plumbed to ?
 

·
Registered
Joined
·
275 Posts
Discussion Starter #84
Well just driving along you should not be in boost at all.

Where do you have it plumbed to ?
Page 4, #31, this threat ...
 

·
Super Moderator
Joined
·
11,140 Posts
That is correct plumbing.

When you are just driving steady state. 60mph etc. You should not be in boost on the gauge.
 

·
Registered
Joined
·
275 Posts
Discussion Starter #86
Has been a while...2nd oil catch can installed...

 

·
Registered
Joined
·
454 Posts
Nice! Which ones are they? Brand?
 

·
Registered
Joined
·
275 Posts
Discussion Starter #88

·
Super Moderator
Joined
·
11,140 Posts

·
Registered
Joined
·
275 Posts
Discussion Starter #90

·
Super Moderator
Joined
·
11,140 Posts
Did you put anything inside your Catch can? Like a 3m scrubbing pad or two. To slow down the vapor stream and catch some particulates? Also you might want to put an O ring or some type of gasket under the little dip stick.

Here is the latest pic. I forgot where I put it.

 

Attachments

·
Registered
Joined
·
275 Posts
Discussion Starter #92
Did you put anything inside your Catch can? Like a 3m scrubbing pad or two. To slow down the vapor stream and catch some particulates? Also you might want to put an O ring or some type of gasket under the little dip stick.

Here is the latest pic. I forgot where I put it.

Actually no, I didn't know about that "optional add ON", but as you are telling me for sure I will add both, thank you Mac, is there a particular way to place the 3M scrubbing pad?, and what's that red cloth sitting at the right bottom of your beautiful pic for?
 

·
Super Moderator
Joined
·
11,140 Posts
There are many things you can use in the catch can to work as vapor control so to speak. Be careful that you dont use anything that has particulates or will succumb to heat.

The rag is an oil check wipe rag. Clean the engine rag. Etc. The bay is clean.
 

·
Registered
Joined
·
275 Posts
Discussion Starter #94
There are many things you can use in the catch can to work as vapor control so to speak. Be careful that you dont use anything that has particulates or will succumb to heat.

The rag is an oil check wipe rag. Clean the engine rag. Etc. The bay is clean.
Thanks Mac, your engine bay is immaculate, I love it!
 

·
Registered
Joined
·
275 Posts
Discussion Starter #95 (Edited)
Another chepo mod, long time due...

 

·
Registered
Joined
·
275 Posts
Discussion Starter #96 (Edited)
...new wrapped hood, old hood was a little rusty so I bought a new one, anti-rust painted and wrapped with carbon fiber vinyl.

 

·
Super Moderator
Joined
·
11,140 Posts
Looks cool !!!
 

·
Registered
Joined
·
275 Posts
Discussion Starter #98

·
Registered
Joined
·
275 Posts
Discussion Starter #100
I like it. I bought a roll of red carbon fiber film to cover my hood but never got around to completing it. Kudos to you for getting it done!
Thank you man, take your time, go slowly, if you tired stop and continue later, keep handy a heat gun or hair drier and a vinyl plastic car squeegee, you really need this to go on, took me few days to complete it.
 
81 - 100 of 115 Posts
Top